QCX+ 5W CW transceiver QRP Labs
QCX+ 5W CW transceiver QRP Labs
Bericht van Hans, van QRP labs:
Hi all,
9,937 QCX kits have been sold since the launch in August 2017. The current batch of kits are almost at an end. Despite the huge number of kits sold to date, the ongoing demand is still very strong. It became apparent to me that regardless of what other new kits come later, there will always be a place in many radio ham's hearts for a high performance, mono-band QRP CW transceiver kit. With its high performance, easy to build and use, CW decoder (including practice mode) and keyer, etc etc., the kit has also proven attractive to newcomers to amateur radio and/or CW.
But I wanted to fix some of the things that have always nagged me at the back of my mind since the start. For the YOTA 2017 summercamp hosted by RSGB in UK, I was under such tight budgetary and time constraints that I had to compromise on certain things. Particularly the inconvenience of fitting the QCX into an enclosure due to the connectors on the two sides, with controls and LCD all at different heights. This has been a distinct disadvantage in many people's mind (though also unleashing much creativity among mechanically inclined constructors).
QCX+ is the replacement for the QCX. No more QCX kits will be made. You can read about the QCX+ here http://qrp-labs.com/qcxp .
The QCX+ development is complete, it is currently in production and will be shipping in mid-June. I am making this announcement now, to allow pre-orders, since the current batch of QCX kits is now practically finished.
But:
QCX+ is the same circuit as QCX.
QCX+ runs the same firmware as QCX.
QCX+ operates just like a QCX.
The changes in QCX+ are as follows (summary, see http://qrp-labs.com/qcxp for full details):
Optional beautiful extruded aluminium enclosure
Much larger PCB. The PCB area is more than doubled. This permits a less dense component installation, following feedback from some constructors who found the QCX PCB rather densely populated. The main PCB is 13 x 10cm (compared to 8 x 10cm in QCX).
Thicker PCB traces (at least 16mil, rather than 12mil in QCX)
Traditional front-panel arrangement: vertical front panel PCB holds LCD and controls, rear horizontal PCB has the main circuits. Pin-headers connect the two.
Power on/off button on front panel
All connectors are on the rear PCB edge
Two additional 3.5mm stereo jack connectors for PTT (50W PA) and CAT control.
2.1mm barrel connector for power
7805 bolts to rear panel for heatsinking
Three BS170 PA transistors and the MPS751 keying envelope transistor are now bolted flat on the PCB for heatsinking purposes - reducing probability of overheating
Lots of pin headers and test pads for debugging, extending, experimenting, modifying etc., including modifying the purpose of the rear panel 3.5mm jack connectors
Plenty of space for modifications and experiments
C24 increased to 470uF (quieter Tx/Rx transitions in full-QSK mode)
Incorporates IC3 pin 13-14 10K resistor mod http://www.qrp-labs.com/qcx/qcxmods/ptt.html
Due to the 2.2x increase in PCB area, additional inter-board connectors, switches, hardware etc., there is a modest increase in price from $49 to $55.
The price of the optional enclosure kit is $25. The combination of QCX+ and QCX+ Enclosure is still cheaper than the combination of QCX and the most popular enclosure (BaMaTech aluminium enclosure).
Manufacturing is already underway and PRE-ORDERING is now open, for shipment in mid-June 2020. See http://shop.qrp-labs.com/qcxp
Comments welcome
73 Hans G0UPL
http://qrp-labs.com
Hi all,
9,937 QCX kits have been sold since the launch in August 2017. The current batch of kits are almost at an end. Despite the huge number of kits sold to date, the ongoing demand is still very strong. It became apparent to me that regardless of what other new kits come later, there will always be a place in many radio ham's hearts for a high performance, mono-band QRP CW transceiver kit. With its high performance, easy to build and use, CW decoder (including practice mode) and keyer, etc etc., the kit has also proven attractive to newcomers to amateur radio and/or CW.
But I wanted to fix some of the things that have always nagged me at the back of my mind since the start. For the YOTA 2017 summercamp hosted by RSGB in UK, I was under such tight budgetary and time constraints that I had to compromise on certain things. Particularly the inconvenience of fitting the QCX into an enclosure due to the connectors on the two sides, with controls and LCD all at different heights. This has been a distinct disadvantage in many people's mind (though also unleashing much creativity among mechanically inclined constructors).
QCX+ is the replacement for the QCX. No more QCX kits will be made. You can read about the QCX+ here http://qrp-labs.com/qcxp .
The QCX+ development is complete, it is currently in production and will be shipping in mid-June. I am making this announcement now, to allow pre-orders, since the current batch of QCX kits is now practically finished.
But:
QCX+ is the same circuit as QCX.
QCX+ runs the same firmware as QCX.
QCX+ operates just like a QCX.
The changes in QCX+ are as follows (summary, see http://qrp-labs.com/qcxp for full details):
Optional beautiful extruded aluminium enclosure
Much larger PCB. The PCB area is more than doubled. This permits a less dense component installation, following feedback from some constructors who found the QCX PCB rather densely populated. The main PCB is 13 x 10cm (compared to 8 x 10cm in QCX).
Thicker PCB traces (at least 16mil, rather than 12mil in QCX)
Traditional front-panel arrangement: vertical front panel PCB holds LCD and controls, rear horizontal PCB has the main circuits. Pin-headers connect the two.
Power on/off button on front panel
All connectors are on the rear PCB edge
Two additional 3.5mm stereo jack connectors for PTT (50W PA) and CAT control.
2.1mm barrel connector for power
7805 bolts to rear panel for heatsinking
Three BS170 PA transistors and the MPS751 keying envelope transistor are now bolted flat on the PCB for heatsinking purposes - reducing probability of overheating
Lots of pin headers and test pads for debugging, extending, experimenting, modifying etc., including modifying the purpose of the rear panel 3.5mm jack connectors
Plenty of space for modifications and experiments
C24 increased to 470uF (quieter Tx/Rx transitions in full-QSK mode)
Incorporates IC3 pin 13-14 10K resistor mod http://www.qrp-labs.com/qcx/qcxmods/ptt.html
Due to the 2.2x increase in PCB area, additional inter-board connectors, switches, hardware etc., there is a modest increase in price from $49 to $55.
The price of the optional enclosure kit is $25. The combination of QCX+ and QCX+ Enclosure is still cheaper than the combination of QCX and the most popular enclosure (BaMaTech aluminium enclosure).
Manufacturing is already underway and PRE-ORDERING is now open, for shipment in mid-June 2020. See http://shop.qrp-labs.com/qcxp
Comments welcome
73 Hans G0UPL
http://qrp-labs.com
CWops #2897
Re: QCX+ 5W CW transceiver QRP Labs
Leuk kitje dat je op een lange avond kunt bouwen. Werkt RX als een speer maar de eindtrapjes (goedkope torretjes trouwens) zijn erg gevoelig voor een slechte SWR of per ongeluk keyen (het is een CW rig...) zonder antenne. Een degelijke eindtrap zou ik hier nog wel eens voor willen zien.
Heb 'm destijds ingebouwd in een kleine behuizing met een LiIon accu en step-up naar 12V en dat werkte fabulous.
Wat de heck, ik haal m weer eens van zolder en dan zet ik er nieuwe torretjes in!
Heb 'm destijds ingebouwd in een kleine behuizing met een LiIon accu en step-up naar 12V en dat werkte fabulous.
Wat de heck, ik haal m weer eens van zolder en dan zet ik er nieuwe torretjes in!
Re: QCX+ 5W CW transceiver QRP Labs
Stiekem wel jammer dat de nieuwe versie een flinke baksteen geworden is ipv een schattig klein doosje... Maarja wél makkelijker te bouwen natuurlijk. Heel veel radio voor het geld!
Re: QCX+ 5W CW transceiver QRP Labs
Ik lees dat er genoeg ruimte is voor een batterij, speaker enz. Dat eventueel zelfs de 50W PA erin zou passen. Ik heb de 40m versie + PA besteld, met behuizingen. Het begin van een rijtje
Respect voor bouwen in een lange avond. Ik heb het moeten verdelen over 2 dagen. Ik las dat het ruim 280 soldeerpunten zijn. Dan nog ringkernen wikkelen...
Respect voor bouwen in een lange avond. Ik heb het moeten verdelen over 2 dagen. Ik las dat het ruim 280 soldeerpunten zijn. Dan nog ringkernen wikkelen...
CWops #2897
- PE2AAB
- Moderator
- Berichten: 7117
- Lid geworden op: 12 apr 2005, 19:06
- Roepletters: PE2AAB
- Locatie: Aalst - Waalre
- Contacteer:
Re: QCX+ 5W CW transceiver QRP Labs
Ik moet eerst het CW’en vaardig worden maar het is wel een héél leuk setje ‘voor weinig’.
'73 Rick, PE2AAB www.pe2aab.nl
- PH2LB
- Berichten: 1432
- Lid geworden op: 06 mar 2013, 20:31
- Roepletters: PH2LB
- Locatie: Almelo/JO32HI
- Contacteer:
Re: QCX+ 5W CW transceiver QRP Labs
Ik zag hem vanmorgen ook voorbij komen in de Groups.IO en moet bekennen dat ik er bijna een besteld had.
Maar heb op moment genoeg QRP-Labs spul in de shack staan (incl QCX40) en heb me voorgenomen dat ik
eerst mijn CW op weer een acceptabel nivo breng voordat ik me toe sta een nieuw QCX+ te kopen
Maar hij is wel heel verleidelijk. Zekers omdat er ruimte is voor mee modificaties (luidspreker, accu's, etc).
Maar heb op moment genoeg QRP-Labs spul in de shack staan (incl QCX40) en heb me voorgenomen dat ik
eerst mijn CW op weer een acceptabel nivo breng voordat ik me toe sta een nieuw QCX+ te kopen
Maar hij is wel heel verleidelijk. Zekers omdat er ruimte is voor mee modificaties (luidspreker, accu's, etc).
73, Lex
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
Re: QCX+ 5W CW transceiver QRP Labs
Ik heb 'm inmiddels gemaakt, inclusief de 50W PA! Het is echt leuk spul, het werkt gewoon goed. Zit vol met handige functies.
Sinds gisteren een handje vol QSO's mee gemaakt en kan zeggen dat de PA wel fijn is
Sinds gisteren een handje vol QSO's mee gemaakt en kan zeggen dat de PA wel fijn is
CWops #2897
- PH2LB
- Berichten: 1432
- Lid geworden op: 06 mar 2013, 20:31
- Roepletters: PH2LB
- Locatie: Almelo/JO32HI
- Contacteer:
Re: QCX+ 5W CW transceiver QRP Labs
Goed bezig. benieuwd naar je ervaringen.
Ik wacht nog met smart op mijn pakket (was er een beetje laat bij, maar kon het niet laten)
Ik wacht nog met smart op mijn pakket (was er een beetje laat bij, maar kon het niet laten)
73, Lex
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
- PH2LB
- Berichten: 1432
- Lid geworden op: 06 mar 2013, 20:31
- Roepletters: PH2LB
- Locatie: Almelo/JO32HI
- Contacteer:
Re: QCX+ 5W CW transceiver QRP Labs
Heeft even geduurd, maar pakketje is binnen gekomen en al lekker aan het bouwen geslagen.
Zoals gebruikelijk met de kits van Hans Summers was er weer een mooie bouw handleiding bij en na 2 (deel) avonden solderen zat hij helemaal in elkaar.
Was weer een heerlijke bouw ervaring en heb alleen spijt dat ik niet gelijk de PA had meebesteld (had ik nog wat te bouwen gehad).
Meer bouw info, foto's en een paar kleinigheden waar ik tegen aangelopen ben, heb ik op mijn website gezet : https://www.ph2lb.nl/blog/index.php?page=qrp-labs-qcxp
Zoals gebruikelijk met de kits van Hans Summers was er weer een mooie bouw handleiding bij en na 2 (deel) avonden solderen zat hij helemaal in elkaar.
Was weer een heerlijke bouw ervaring en heb alleen spijt dat ik niet gelijk de PA had meebesteld (had ik nog wat te bouwen gehad).
Meer bouw info, foto's en een paar kleinigheden waar ik tegen aangelopen ben, heb ik op mijn website gezet : https://www.ph2lb.nl/blog/index.php?page=qrp-labs-qcxp
73, Lex
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
Re: QCX+ 5W CW transceiver QRP Labs
Mooi spul, las op je website dat je 'm hebt omgebouwd naar 20m. Dat snap ik wel. De 50W PA kan ik je zeker aanraden.
Heb laatst een Rev 3. 30m QCX gerepareerd (laag vermogen) en gemodifieerd met de laatste verbetereingen zoals de keying envelope aanpassing. Er komt nu wel 5W uit bij 15V. Heb 'm vanmiddag laten draaien op 9V (1,4W) met WSPR, met een portable antenne (en tuner) in de tuin. Leuk spul.
Ik kijk uit naar de QCX mini
Heb laatst een Rev 3. 30m QCX gerepareerd (laag vermogen) en gemodifieerd met de laatste verbetereingen zoals de keying envelope aanpassing. Er komt nu wel 5W uit bij 15V. Heb 'm vanmiddag laten draaien op 9V (1,4W) met WSPR, met een portable antenne (en tuner) in de tuin. Leuk spul.
Ik kijk uit naar de QCX mini
CWops #2897
- PH2LB
- Berichten: 1432
- Lid geworden op: 06 mar 2013, 20:31
- Roepletters: PH2LB
- Locatie: Almelo/JO32HI
- Contacteer:
Re: QCX+ 5W CW transceiver QRP Labs
De 50 W PA heb ik al liggen voor mijn QCX voor 40m. Heel leuk bouwpakketje voor net dat beetje meer punch op de banden.pa2st schreef:Mooi spul, las op je website dat je 'm hebt omgebouwd naar 20m. Dat snap ik wel. De 50W PA kan ik je zeker aanraden.
Heb laatst een Rev 3. 30m QCX gerepareerd (laag vermogen) en gemodifieerd met de laatste verbetereingen zoals de keying envelope aanpassing. Er komt nu wel 5W uit bij 15V. Heb 'm vanmiddag laten draaien op 9V (1,4W) met WSPR, met een portable antenne (en tuner) in de tuin. Leuk spul.
Ik kijk uit naar de QCX mini
De keying envelope aanpassing moet ik nog doorvoeren, maar heb al tijden niet gesleuteld met dat ding (mijn CW is echt verwaarloosd).
Ja ben benieuwd wat Hans met die QCX mini voor elkaar gaat krijgen. Tijdens de Zoom meting (staat op youtube : https://www.youtube.com/watch?v=0qa3wMkMhsU ) liet hij al een kastje zien. Wordt een mooi compact ding.
73, Lex
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
- PH2LB
- Berichten: 1432
- Lid geworden op: 06 mar 2013, 20:31
- Roepletters: PH2LB
- Locatie: Almelo/JO32HI
- Contacteer:
Re: QCX+ 5W CW transceiver QRP Labs
De stock behuizing van de QCX+ heeft als nadeel dat hij bij gebruik op de tafel de ergonomie niet optimaal is. Draaien aan de knoppen levert stress op in de pols en in de groups.io/QRPLabs beschreef Larry N6NC hetzelfde probleem. Ik liet hem de kantelvoeten zien die ik voor mijn uBITX had gemaakt maar deze zijn vrij groot. Gisteravond heb even de tijd genomen om een speciale set voor de QCX+ te ontwerpen.
Het is nog niet klaar (misschien wil ik een beetje groter worden, waardoor de behuizing een grote opheffende hoek krijgt.
Meer foto's, info en het Tinkercad ontwerp is te vinden op mijn website : https://www.ph2lb.nl/blog/index.php?pag ... -qcxp#tilt
Het is nog niet klaar (misschien wil ik een beetje groter worden, waardoor de behuizing een grote opheffende hoek krijgt.
Meer foto's, info en het Tinkercad ontwerp is te vinden op mijn website : https://www.ph2lb.nl/blog/index.php?pag ... -qcxp#tilt
73, Lex
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
- PE2AAB
- Moderator
- Berichten: 7117
- Lid geworden op: 12 apr 2005, 19:06
- Roepletters: PE2AAB
- Locatie: Aalst - Waalre
- Contacteer:
Re: QCX+ 5W CW transceiver QRP Labs
Wat een interessante Blog! Leuk on je bouwervaringen te lezen Lex!
'73 Rick, PE2AAB www.pe2aab.nl
- PH2LB
- Berichten: 1432
- Lid geworden op: 06 mar 2013, 20:31
- Roepletters: PH2LB
- Locatie: Almelo/JO32HI
- Contacteer:
Re: QCX+ 5W CW transceiver QRP Labs
Dank je.PE2AAB schreef:Wat een interessante Blog! Leuk on je bouwervaringen te lezen Lex!
73, Lex
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB
"Computers are fun, but there is more between one and zero"
www.ph2lb.nl . . . . facebook.com/PH2LB